140mm Recticel Eurothane GP PIR Insulation Board 2.4m x 1.2m - 2.88m2 per sheet
At 140mm, Recticel Eurothane GP is among the highest-performing boards in the general purpose range: a closed-cell polyisocyanurate (PIR) core faced on both sides with a gas diffusion tight, low-emissivity foil, made for pitched roofs, timber and metal framed walls, and floors, including those running underfloor heating.
Supplied as a single 2400mm x 1200mm board covering 2.88m², it carries a declared thermal resistance (R-value) of 6.35 m²K/W from a declared thermal conductivity of 0.022 W/mK. That is among the most a single Eurothane GP board can deliver, which is why 140mm is reached for on floors and roofs working to low U-value targets without resorting to two layers.
Laid in a tightly butted, brick-bond pattern with taped joints, the straight edges keep the insulation layer continuous and limit thermal bridging, while the printed grid guides accurate cutting. The low-emissivity foil facings support thermal performance against an adjacent air space, and the closed-cell core resists moisture and holds its shape for the life of the building.
In floors it is laid over a damp-proof membrane in solid and suspended construction and to upgrade existing slabs; in pitched roofs it goes between, over or below the rafters; in framed walls it fits between the studs or as a continuous lining, and it can line solid masonry internally. Where a project demands even more, two boards combine with staggered joints. Install in line with current Recticel technical guidance and the project specification, and finish internal walls with plasterboard rather than plaster or paint applied directly. On new build held to tighter U-values and on major refurbishment alike, 140mm Eurothane GP delivers top-of-range single-layer performance from a board that still handles and cuts easily.
Key Benefits of 140mm Recticel Eurothane GP:
- Rigid PIR insulation board for pitched roofs, framed walls and floors, including underfloor heating build-ups.
- Declared R-value (thermal resistance) of 6.35 m²K/W at 140mm, among the highest in the GP range.
- Declared thermal conductivity of 0.022 W/mK for high single-layer thermal performance.
- Straight edges that butt tightly in a brick-bond pattern to keep joints closed and limit thermal bridging.
- Gas diffusion tight, low-emissivity foil facings on both sides, with a printed grid to guide cutting.
- Closed-cell PIR core that resists moisture and stays dimensionally stable.
- Compressive strength of at least 120 kPa, supporting use within floor build-ups (check the full system requirements).
- Combines in two staggered layers where the deepest build-ups are required.
- Lightweight for its thickness and easy to cut with a sharp knife or insulation saw.
- Manufactured with blowing agents that have zero Ozone Depletion Potential (ODP) and low Global Warming Potential (GWP).
- Supplied as a single 2400mm x 1200mm board covering 2.88m².
Good to know:
- Although the closed-cell core is moisture resistant, PIR is not waterproof: store boards flat, dry, off the ground and out of direct sunlight, and avoid point loads or walking on stacked boards.
- A standard board is 2.4m x 1.2m, giving 2.88m² coverage per board.
- For the deepest build-ups, install two layers with staggered, tightly butted joints (thicker layer outermost) and tape the joints.
- Bespoke cutting is available, find out more here.
- Recticel's pitched roof and floor specification guides are useful references for rafter and floor build-ups.
When a floor or warm roof has to reach a low U-value without stacking layers, 140mm Recticel Eurothane GP answers with a declared 6.35 m²K/W of single-layer resistance and the same easy handling as the rest of the range.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
140mm Recticel Eurothane GP PIR Insulation Board 2.4m x 1.2m - 2.88m2 per sheet
140mm Recticel Eurothane GP PIR Insulation Board 2.4m x 1.2m - 2.88m2 per sheet
At 140mm, Recticel Eurothane GP is among the highest-performing boards in the general purpose range: a closed-cell polyisocyanurate (PIR) core faced on both sides with a gas diffusion tight, low-emissivity foil, made for pitched roofs, timber and metal framed walls, and floors, including those running underfloor heating.
Supplied as a single 2400mm x 1200mm board covering 2.88m², it carries a declared thermal resistance (R-value) of 6.35 m²K/W from a declared thermal conductivity of 0.022 W/mK. That is among the most a single Eurothane GP board can deliver, which is why 140mm is reached for on floors and roofs working to low U-value targets without resorting to two layers.
Laid in a tightly butted, brick-bond pattern with taped joints, the straight edges keep the insulation layer continuous and limit thermal bridging, while the printed grid guides accurate cutting. The low-emissivity foil facings support thermal performance against an adjacent air space, and the closed-cell core resists moisture and holds its shape for the life of the building.
In floors it is laid over a damp-proof membrane in solid and suspended construction and to upgrade existing slabs; in pitched roofs it goes between, over or below the rafters; in framed walls it fits between the studs or as a continuous lining, and it can line solid masonry internally. Where a project demands even more, two boards combine with staggered joints. Install in line with current Recticel technical guidance and the project specification, and finish internal walls with plasterboard rather than plaster or paint applied directly. On new build held to tighter U-values and on major refurbishment alike, 140mm Eurothane GP delivers top-of-range single-layer performance from a board that still handles and cuts easily.
Key Benefits of 140mm Recticel Eurothane GP:
- Rigid PIR insulation board for pitched roofs, framed walls and floors, including underfloor heating build-ups.
- Declared R-value (thermal resistance) of 6.35 m²K/W at 140mm, among the highest in the GP range.
- Declared thermal conductivity of 0.022 W/mK for high single-layer thermal performance.
- Straight edges that butt tightly in a brick-bond pattern to keep joints closed and limit thermal bridging.
- Gas diffusion tight, low-emissivity foil facings on both sides, with a printed grid to guide cutting.
- Closed-cell PIR core that resists moisture and stays dimensionally stable.
- Compressive strength of at least 120 kPa, supporting use within floor build-ups (check the full system requirements).
- Combines in two staggered layers where the deepest build-ups are required.
- Lightweight for its thickness and easy to cut with a sharp knife or insulation saw.
- Manufactured with blowing agents that have zero Ozone Depletion Potential (ODP) and low Global Warming Potential (GWP).
- Supplied as a single 2400mm x 1200mm board covering 2.88m².
Good to know:
- Although the closed-cell core is moisture resistant, PIR is not waterproof: store boards flat, dry, off the ground and out of direct sunlight, and avoid point loads or walking on stacked boards.
- A standard board is 2.4m x 1.2m, giving 2.88m² coverage per board.
- For the deepest build-ups, install two layers with staggered, tightly butted joints (thicker layer outermost) and tape the joints.
- Bespoke cutting is available, find out more here.
- Recticel's pitched roof and floor specification guides are useful references for rafter and floor build-ups.
When a floor or warm roof has to reach a low U-value without stacking layers, 140mm Recticel Eurothane GP answers with a declared 6.35 m²K/W of single-layer resistance and the same easy handling as the rest of the range.
Original: $60.65
-65%$60.65
$21.23Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
At 140mm, Recticel Eurothane GP is among the highest-performing boards in the general purpose range: a closed-cell polyisocyanurate (PIR) core faced on both sides with a gas diffusion tight, low-emissivity foil, made for pitched roofs, timber and metal framed walls, and floors, including those running underfloor heating.
Supplied as a single 2400mm x 1200mm board covering 2.88m², it carries a declared thermal resistance (R-value) of 6.35 m²K/W from a declared thermal conductivity of 0.022 W/mK. That is among the most a single Eurothane GP board can deliver, which is why 140mm is reached for on floors and roofs working to low U-value targets without resorting to two layers.
Laid in a tightly butted, brick-bond pattern with taped joints, the straight edges keep the insulation layer continuous and limit thermal bridging, while the printed grid guides accurate cutting. The low-emissivity foil facings support thermal performance against an adjacent air space, and the closed-cell core resists moisture and holds its shape for the life of the building.
In floors it is laid over a damp-proof membrane in solid and suspended construction and to upgrade existing slabs; in pitched roofs it goes between, over or below the rafters; in framed walls it fits between the studs or as a continuous lining, and it can line solid masonry internally. Where a project demands even more, two boards combine with staggered joints. Install in line with current Recticel technical guidance and the project specification, and finish internal walls with plasterboard rather than plaster or paint applied directly. On new build held to tighter U-values and on major refurbishment alike, 140mm Eurothane GP delivers top-of-range single-layer performance from a board that still handles and cuts easily.
Key Benefits of 140mm Recticel Eurothane GP:
- Rigid PIR insulation board for pitched roofs, framed walls and floors, including underfloor heating build-ups.
- Declared R-value (thermal resistance) of 6.35 m²K/W at 140mm, among the highest in the GP range.
- Declared thermal conductivity of 0.022 W/mK for high single-layer thermal performance.
- Straight edges that butt tightly in a brick-bond pattern to keep joints closed and limit thermal bridging.
- Gas diffusion tight, low-emissivity foil facings on both sides, with a printed grid to guide cutting.
- Closed-cell PIR core that resists moisture and stays dimensionally stable.
- Compressive strength of at least 120 kPa, supporting use within floor build-ups (check the full system requirements).
- Combines in two staggered layers where the deepest build-ups are required.
- Lightweight for its thickness and easy to cut with a sharp knife or insulation saw.
- Manufactured with blowing agents that have zero Ozone Depletion Potential (ODP) and low Global Warming Potential (GWP).
- Supplied as a single 2400mm x 1200mm board covering 2.88m².
Good to know:
- Although the closed-cell core is moisture resistant, PIR is not waterproof: store boards flat, dry, off the ground and out of direct sunlight, and avoid point loads or walking on stacked boards.
- A standard board is 2.4m x 1.2m, giving 2.88m² coverage per board.
- For the deepest build-ups, install two layers with staggered, tightly butted joints (thicker layer outermost) and tape the joints.
- Bespoke cutting is available, find out more here.
- Recticel's pitched roof and floor specification guides are useful references for rafter and floor build-ups.
When a floor or warm roof has to reach a low U-value without stacking layers, 140mm Recticel Eurothane GP answers with a declared 6.35 m²K/W of single-layer resistance and the same easy handling as the rest of the range.
